VIBRATORY PLATE COMPACTORS INSTRUCTION MANUAL
BARTELL MORRISON INC. BARTELL MORRISON (USA) LLC
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX 905-364-4201
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-5400 FAX 732-566-5444
Created: 11/10
Revised: 06/14
- 10 -
OPERATION
1. In operation, guide the machine, but let the
compactor do the work. Bearing down on the handle
is unnecessary and causes shock absorber wear.
2. On level surfaces the compactor moves forward
rapidly. On uneven surfaces or inclines, light
forward pressure on handle may be required to
assist the compactor in moving forward.
3. ALWAYS OPERATE THE MACHINE AT FULL
THROTTLE. If excessive vibration is felt through the
handle, do not operate until the engine is checked
and set at its maximum running speed of 3600 rpm.
Insure the drive belt is adjusted properly. Refer to
belt tension section.
4. The handle has a spring loaded locking mechanism
to keep it upright in storage. DO NOT OPERATE
THE MACHINE WITH THE HANDLE IN THE
STORAGE POSITION. To unlock the handle, push
it to the left and pull back to operation position.
LUBRICATION
ENGINE OIL
Always check engine oil before starting and at
regular intervals thereafter. Use proper engine oil as
recommended – see chart below. Keep engine oil
clean, change accordingly. Fill crankcase to levels
as recommended in manufacturer’s engine manual.
EXCITER HOUSING
The exciter housing is pre-serviced using exactly 4
½ oz.of EXXON (ESSO) NUTO H-32 oil or its
equivalent.
MAINTENANCE
Maintaining your compactor will insure long life to the
machine and its components.
AIR CLEANER - Keep air filter clean at all times. Wash
away dust and debris using a non-oil based cleaning
solvent. Let the filter dry before re-installing.
LUBRICATION – Always check engine oil regularly.
Use proper engine oil as recommended. See chart
below. Fill crankcase to levels as recommended in
manufacture’s engine manual.
SPARK PLUG
– Check and clean spark plugs
regularly. A fouled, dirty or carboned spark plug causes
hard starting and poor engine performance. Set spark
plug gap to recommended clearance. Refer to engine
manual.
BELT TENSION – IMPORTANT!
If there is excessive belt play, there will be a decrease
in the impact force and erratic vibration, which could
cause machine damage. The normal belt play should
be 1/2” to 5/8” which is attained by depressing the top
section of the belt at the belt guard mounting bracket
location. When adjusting the belt make sure that the
clutch is in alignment with exciter pulley. Tighten all
engine mount bolts, adjust the two engine-stop bolts,
and tighten lock nuts.
STORAGE
The following steps should be taken to prepare your plate
compactor for extended storage.
1. Close fuel shut off valve.
2. Siphon excess gasoline from tank.
3. Start engine until it stops from lack of fuel. This will
use up all the fuel in the carburetor and prevent
formation of deposits due to evaporation of fuel.
4. Remove spark plug and pour 2 oz. of SAE 10W-30
motor oil into the cylinder. Slowly crank the engine 2
or 3 times to distribute the oil throughout the cylinder.
This will help prevent rust during storage. Replace
spark plug.
5. Store the unit in an upright position in a cool, dry,
well ventilated area.
Season Temperature Grade of En
ine Oil
All Season SAE 10W-30
(23 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals