Bartell B436 Owner's Manual download pdf (Page 12)

WALK BEHIND POWER TROWEL INSTRUCTION MANUAL

OPERATION (Floating)

When the slab has set sufficiently firm that the

operator’s footprint leaves a very slight depression on

the surface of the slab, it is ready for the floating

operation.

Under normal operating conditions the machine should

cover as much as 1000 sq. ft. in about 15 minutes. It is

recommended that a slight tension on the trowel control

cable, (but not a definite tilt), during the floating

operation will cause the machine to operate much

smoother. After the floated slab has set sufficiently, it is

ready for the finishing operation.

OPERATION (Finishing)

When starting the finishing operation, never set the

trowels up over 1/4” pitch. This is important. Guiding the

machine on the slab is very simple, a slight upward lift of

the handle causes the machine to travel to the left.

Holding the handle in the neutral position, will slowly

cause the machine to spin in one spot. Slight downward

pressure on the handle causes the machine to travel to

the right. Best results are obtained by covering

approximately 4” on each turn. In other words, let the

machine move right or left, backwards or forwards,

approximately 4” with each revolution of the trowels. To

fill a hole or cut down a hump, move the unit back and

forth over the problem area.

After the first pass over the slab, the waiting time

between operations is determined in the same manner

as if you were hand troweling. To repeat; the entire

application and action of the troweling machine in regard

to getting on the slab, and the correct pitch of the

trowels, is determined in the same manner as would be

used by a cement finisher when troweling by hand.

STARTING PROCEDURE:

*WARM CLIMATE

Open fuel valve on gas tank. Set throttle lever to “Fast”

idle position, set choke to closed position, start engine.

Open choke slightly to prevent flooding. Move to “Open”

or “Run” position when engine is warm, increase throttle

to maximum operation position (3600 rpm).

STARTING PROCEDURE: *COLD CLIMATE

Follow same procedure as above but allow longer

warm-up period – 3 to 5 minutes. In cold weather, oil is

much heavier to move and requires more time to work

its way into the moving parts. If maximum power is not

attained, allow further warm-up time. Fill fuel tank with

clean gasoline, use safety approved gas containers.

DO NOT MIX OIL WITH GASOLINE – USE UNLEADED

GAS ONLY.

STOPPING PROCEDURE

1. Throttle engine down.

2. Turn off stop switch.

LUBRICATION

1. ENGINE OIL

The long life and successful operation of any piece of

machinery is dependent on frequent and thorough

lubrication.

Before using the trowel, always check your engine for

oil. Use proper engine oil as recommended in the

engine manufacturer’s manual. Fill crankcase to

levels as recommended.

ENGINE OIL SPECIFICATIONS

2. SPIDER PLATE

There are 4 (four) grease fittings on the spider plate,

each must be greased daily. THE SPIDER PLATE

MUST BE GREASED EVERY TIME MACHINE IS

USED.

3. GEARBOX

Check the oil level sight plugs on both gearboxes

daily to ensure the oil is half way on the site glass.

Top up with Agma 8 compounded gear oil only.

Gearbox capacity 16 oz. to 19 oz. (473ml. To 562ml.)

Example: Esso/Exxon Cylesstic TK680.

4. TO CHANGE GEARBOX OIL

Place a pan beneath the drain plug to catch the oil.

Remove the drain plug and the filler plug from the

gearbox. After the oil has drained completely, replace

the drain plug and tighten. Fill the gearbox through

the filler plug with 16 oz. to 19 oz. (473ml. To 562ml.)

of Agma 8 compounded gear oil. Replace the filler

plug and tighten.

CAUTION:

Do not let the machine stand in one spot on the

soft cement. Lift from the slab when the floating

operation is complete.

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA L5T 3A7, 905-364-4200 FAX 905-364-4201

CREATED: 07/04

REVISED: 05/10